How to Replace a Master Cylinder: 6 Steps (with Pictures) (2024)

Get Car Support Solve Any Problem

Download Article

1. 1

   Locate the various components of the vehicle's brake system.^[1]

   • Use your vehicle's manual to identify these components.
   • Locate the brake fluid reservoir, the brake master cylinder, the brake fluid level sensor, and the brake fluid lines.
   • The brake fluid reservoir is usually at the top of the brake system and contains brake fluid. It can be identified by the presence of a threaded cap on top of it.
   • The brake master cylinder is typically located directly beneath the brake fluid reservoir.
2. 2

   Remove the brake fluid from the brake fluid reservoir.^[2]

   • Remove the cap.
   • Use a siphon or turkey baster to remove the brake fluid.
   • Dispose of or recycle the brake fluid in accordance with local laws and regulations. Contact your local agency that deals with household hazardous wastes for any needed information.^[3]

   Advertisem*nt

3. 3

   Remove the brake fluid sensor connector.^[4]

   • This is part of the brake fluid level sensor that you previously identified from your vehicle's manual.
   • This can often be removed by pulling it with your hand.
   • Follow the instructions in your vehicle's manual.
4. 4

   Remove the brake fluid lines.

   • Loosen the brake fluid lines with a line wrench.
   • Twist the line wrench in a counter-clockwise motion on each brake fluid line until all of them have been removed.
   • Keep a towel or cloth handy to clean up any brake fluid that leaks as a result of this procedure.
5. See Also

   How to Replace a Brake Master CylinderHow to Replace a Brake Master Cylinder | YourMechanic Advice

   5

   Detach the brake master cylinder.^[5]

   • Use a socket wrench to remove the mounting bolts from the brake master cylinder. These bolts can be located in your vehicle's manual.
   • Remove the brake master cylinder by hand.
6. 6

   Install the new brake master cylinder.^[6]

   • Put the new brake master cylinder in place of the old cylinder.
   • Connect the mounting bolts with a socket wrench.
   • Tighten to prescribed torque or at least as tight as the old ones were.
   • Fill the fluid reservoir with fluid allowing some to run out the brake pipe holes.
   • Get somebody to gently pump the brakes while holding a container under the holes.
   • This "primes" the cylinder and purges excess air.
   • Reconnect the brake fluid lines by turning a line wrench clockwise.
   • Reconnect the brake fluid sensor according to the instructions in the vehicle's manual.
   • Use the type of brake fluid that is listed on the cap or in your vehicle's manual.
   • Bleed the new brake master cylinder.
   • Optional - remove front wheel from furthest hub. Push brake cylinder back.
   • Optional - remove other front wheel. Push brake cylinder back.
   • Optional - If you do this watch for reservoir overflow, catch as required.
   • Optional - This effects a "reverse bleed" that releases some air close to the master cylinder.
   • Optional - pump brake pedal to return cylinders, top up fluid as required.
   • These optional steps make the subsequent bleeding much easier because the air is close to the master cylinder.
   • Check pedal free play. If there is an adjuster on pedal adjust to take up slack BUT do not allow no free play. Brakes will bind.
   • Brakes must be bled after master cylinder replacement.
   • Purchase a bleeder kit from an automotive supply store.
   • Follow the directions that come with the kit.

Advertisem*nt

Community Q&A

Ask a Question

• If you are uncertain as to whether or not the brake master cylinder must be replaced, check it for fluid leaks. A fluid leak indicates that it must be replaced immediately.

  Thanks

  Helpful12Not Helpful4

• Brake bleeding is a two person process. Don't even bother until you have a friend.

  Thanks

  Helpful3Not Helpful4

• Bleed the front wheels first. See how it goes - you may not have to bleed all four wheels.

  Thanks

  Helpful0Not Helpful6

Show More Tips

• Do not attempt this if you are a novice or "first timer". Even a small mistake can prove deadly to yourself and others. This is one of the most vital parts of the car. If you are not 100% confident, take it to a shop!

  Thanks

  Helpful1Not Helpful0

• Test the brakes before driving in traffic. Press and hold the pedal down. It should stay solid. Confirm that the brakes can hold the car - easy with an auto - put the car in drive and with the brake on apply a bit of gas. Car should not move. At your first opportunity, while driving at around 30km/h (19mph), check the rear view mirror, if clear, then apply the brakes quite firmly.

  Thanks

  Helpful0Not Helpful1

• If you opt to take the vehicle to an auto mechanic instead of fixing it yourself, exercise caution by driving slowly and allowing plenty of room between your vehicle and other vehicles. Have the vehicle towed if the vehicle's braking ability has been severely reduced or if it no longer works at all.

  Thanks

  Helpful0Not Helpful4

You Might Also Like

Co-authors: 17

Updated: February 15, 2024

Views:351,400

Categories: Car Brakes

Russian